
Tumblast Shot Blasting Machine
For batches of small castings, forgings, nuts and bolts. Parts tumble on a rubber belt under the blast.
Kleenwell builds Tumblast, hanger type and roller conveyor shot blasting machines that strip rust, scale and sand from metal parts in minutes, ready for paint.
Built to last
Heavy steel, wear parts in Ni-Hard and manganese
Full range
Seven machine types and 50+ spare parts
Made in Jalandhar
Designed and fabricated in our own works
Spares & service
From enquiry to installation and after
Types of shot blasting machines we make, each built to your part size and daily output.

For batches of small castings, forgings, nuts and bolts. Parts tumble on a rubber belt under the blast.

For large, heavy or delicate parts. They hang on a hook and turn in front of the blast wheels.

For steel plates, beams and pipes. Rollers carry the work through the blast without stopping.

For flat or fragile parts that should not tumble. The table turns slowly under the blast.

Pulse-jet industrial dust collector that keeps your shop clean. Fits any blasting machine.

Manual blasting with a hand-held nozzle, for big, odd-shaped or on-site jobs.

Pulls iron pieces out of foundry sand and abrasive so they can be reused.
Rust, scale and sand off, clean grey metal out. Filmed and photographed at our customers' works.




Seven short clips of the shot blasting process, filmed at our works in Jalandhar. Swipe or use the arrows to go through them in order.
Rusty, scaly metal parts come in. Paint will not stick to them like this.
The operator hangs the parts on a hook inside the machine, spaced apart so every side gets cleaned.
Heavy doors seal the chamber, so the steel shot stays inside.
Blasting time is set at the control panel and the machine is started.
Behind the doors, a fast-spinning wheel throws steel shot at the turning parts and knocks the rust off.
See what happens inside ↓Motors drive an elevator that collects the used shot, cleans it and sends it back to the wheel. Nothing is wasted.
The doors open on clean, bright metal, ready to paint, weld or powder coat.
An animated cutaway of a Tumblast shot blasting machine: the blast wheel, elevator, separator and dust collector. Tap a step to zoom in on that part.
Wear parts in Ni-Hard, high manganese and alloy steel for tumble type, R.L.M. and DISA-type machines. In stock and made to size.

A shot blasting machine cleans metal parts by throwing steel shot at them. It removes rust, mill scale, burnt foundry sand and old paint from castings, forgings, fabricated steel, pipes and sheets, so that paint, powder coating or welding holds properly.
A blast wheel spinning at high speed throws steel shot onto the parts. The impact removes rust, scale and sand. The shot is lifted back by an elevator, cleaned in a separator and thrown again, while a dust collector removes the dust. Read the full shot blasting process.
The price depends on the type of machine, the size of your parts and how much you need to clean each day. Send us your part size and daily quantity, and we will send a quotation for the right Kleenwell machine. See what affects the price.
Wheel blast machines mainly use round steel shot, and sometimes angular steel grit for a rougher profile. Both are hard and can be reused many times inside the machine.
Tumblast machines suit batches of small castings and forgings. Hanger type machines suit large, heavy or delicate parts. Roller conveyor machines suit plates, beams and pipes, and swing table machines suit flat parts that must not tumble. Compare the machine types, or call us and we will advise.
Shot blasting uses a fast-spinning wheel to throw steel shot, which is recovered, cleaned and reused inside a closed machine. Sand blasting uses compressed air and a hand-held nozzle, which suits large, fixed or one-off jobs that cannot go into a machine. Compare shot blasting and sand blasting.
Yes. We supply shot blasting machine spare parts such as blades, control cages, liners and rubber belts, and our team services the machines we build. See all spare parts.
Our works is at 228/2, Hargobind Nagar, G.T. Road, near Pathankot Chowk Bye Pass, Jalandhar, Punjab 144001. We are open Monday to Saturday, 10:00 to 18:00.
Call or WhatsApp us with your part size and daily quantity. We will suggest the right machine and send a price.
Tell us what you need to clean. We will suggest the right machine and send you a quotation.
Thank you. Our team will call you shortly.